i have a ini file and in this file i have some declarations and the compl. number of the different tasks!
Here in this file i have 4
the prog... read the ini file and the compl. nr of declarations. then it begin at the last... her nr 4 and there it read the
bregnextrundate and bregnextruntime
after the nr 4 it read the nr 3 then 2 and so on
I have the Problem, it read the nr 4 (first one) then it read
bregnextrundate and bregnextruntime thats ok, but at the next stepp (read nr 3) it doesent read bregnextrundate and bregnextruntime and so on ... the same on nr 2 and nr 1 and if it beginns from the start again (count down to 0 it begin again on 4) it is the same on the task 4 task 3 and so on....
so... it read only one time at the start from the prog the value and not again.
But why? what have i do wrong?
Sry about my bad english!
here the ini file:
*********************************
//*** Variablen declaration ***
//Dynamicvariable
[task_all]
breganzahl=4
[1]
bregnextrundate=27.11.2013
bregnextruntime=22:43:00
breguser=1
bregpass=2
bregmail=3
bregbirth=
bregprovider=
bregstate=
[2]
bregnextrundate=27.11.2013
bregnextruntime=22:45:00
breguser=4
bregpass=5
bregmail=6
bregbirth=
bregprovider=
bregstate=
[3]
bregnextrundate=27.11.2013
bregnextruntime=21:11:00
breguser=7
bregpass=8
bregmail=9
bregbirth=
bregprovider=
bregstate=
[4]
bregnextrundate=28.11.2013
bregnextruntime=22:46:00
breguser=a
bregpass=b
bregmail=c
bregbirth=
bregprovider=
bregstate=
************************
here is the prog:
************************
//***Umgebung Festlegen***
Let>RP_WINDOWMODE=1
Let>RP_DISPLAYERROR=0
Let>IGNOREERRORS=1
Let>RP_ADMIN=1
//***Install Ordner ermitteln***
//****************************************************************************
//Folgende Zeilen sind nur bei Entwicklung ausgeschaltet, müssen für inst. wieder eingeschaltet werden
//RegistryReadKey>HKEY_CURRENT_USER,Software\PSNET,Installation,strFolderName
//****************************************************************************
//Nächste Zeile legt den install ordner für die Entwicklungsphase fest
Let>strFolderName=D:\Temp
//****************************************************************************
Label>Start
//***Aktive Anzahl der Tasks aus File laden***
ReadIniFile>%strFolderName%\PSNET\Sheet\bregruntime.ini,task_all,breganzahl,bregtaskall
Let>a=%bregtaskall%
Label>bregTaskcheck
IF>a>0
//***Werte aus ini File lesen für entsprechende Task Nr***
ReadIniFile>%strFolderName%\PSNET\Sheet\bregruntime.ini,%a%,bregnextrundate,bregnextrundate
ReadIniFile>%strFolderName%\PSNET\Sheet\bregruntime.ini,%a%,bregnextruntime,bregnextruntime
//***Aktuelles Datum ermitteln***
GetDate>current_date
//***Aktuelle Uhrzeit ermitteln***
Gettime>current_time
If>%current_date%=%bregnextrundate%
If>%current_time%=%bregnextruntime%
Message>Date and time arrived from Task %a%
Endif
Endif
Let>a=a-1
//CPU entlasten im nächsten Schritt
wait>0.0005
ELSE
Goto>Start
ENDIF
Goto>bregTaskcheck
Exit
************************
